Gripper¶
The commands of gripper mode (#Gripper 1, saved).
Send_gripper_data_pack¶
ID 61host → driver0 or 5 bytesPython: Send_gripper_data_pack()
The gripper command, for a driver set up as a gripper (#Gripper 1, saved). Position, speed and the current limit of the move, plus the activate, action and E-stop bits. A move is carried out only while the gripper is calibrated, activated and the action bit is 1. An empty frame (0 bytes) only asks for the state.
5 bytes
| Byte | Bit | Field | Type | Meaning |
|---|---|---|---|---|
| 0 | Position | unsigned 8-bit | 0 fully open, 255 fully closed | |
| 1 | Speed | unsigned 8-bit | 0 slowest, 255 fastest | |
| 2-3 | Current | signed 16-bit | current limit of the move in mA; not clamped by the firmware, not even to the driver's 2800 mA; see the gripper manual for the safe range | |
| 4 | 7 | Activate | bit | 1 activate the gripper, 0 deactivate |
| 4 | 6 | Action | bit | 1 go to the position, 0 idle |
| 4 | 5 | E-stop | bit | 1 raises the gripper E-stop error, again on every control cycle until a frame with this bit 0 arrives; then Send_Clear_Error |
| 4 | 4 | Release direction | bit | read by the firmware but not used |
The driver answers with Respond_Gripper_data_pack.
Send_gripper_calibrate¶
ID 62host → driver0 bytesPython: Send_gripper_calibrate()
Starts the gripper calibration (the jaws find their end stops). Needed after every power-up.
The driver does not answer this command.
Respond_Gripper_data_pack¶
ID 60driver → host4 bytes
The driver's answer to Send_gripper_data_pack: position, measured current, and the state bits. Python attributes gripper_position, gripper_current, gripper_activated, gripper_action_status, gripper_object_detection, gripper_temperature_error, gripper_timeout_error, gripper_estop_error, gripper_calibrated.
The frame (4 bytes)
| Byte | Bit | Field | Type | Meaning |
|---|---|---|---|---|
| 0 | gripper_position | unsigned 8-bit | 0 fully open, 255 fully closed | |
| 1-2 | gripper_current | signed 16-bit | measured current in mA | |
| 3 | 7 | gripper_activated | bit | 1 activated |
| 3 | 6 | gripper_action_status | bit | the action bit of the last Send_gripper_data_pack (1 after #Grippos); the driver never clears it, so it stays 1 after the move ends: the object detection tells when the move has ended |
| 3 | 5-4 | gripper_object_detection | 2 bits | bit 5 is the low bit, bit 4 the high bit: 0 moving, 1 object detected while closing, 2 object detected while opening, 3 at the position |
| 3 | 3 | gripper_temperature_error | bit | a copy of the thermistor temperature error |
| 3 | 2 | gripper_timeout_error | bit | a copy of the CAN watchdog error (Send_Watchdog), not a move timeout |
| 3 | 1 | gripper_estop_error | bit | the E-stop bit of Send_gripper_data_pack (or #Gripstop 1) was set |
| 3 | 0 | gripper_calibrated | bit | 1 calibrated |
Comments
Found a mistake on this page? Edit it on GitHub · Report it · Get help · This page as Markdown · llms.txt · The whole manual as PDF